Phones answered 24/7Longmont, Colorado
Call (833) 490-5225
Serving Boulder County

Structural drying after water damage in Longmont

Drying the framing and subfloor stops water damage from spreading. Moisture readings decide when the house is dry.

  • Phones answered 24/7
  • St. Vrain flood history
  • Frozen and burst pipes
  • Old Town and West Side houses

Get a fast quote

Fastest: call (833) 490-5225. Or send this and we call you back.

Structural Drying

Structural Drying: what it covers

Quick answer

Structural drying removes moisture from the building parts that hold a house together, including framing, subfloor, sheathing and the inside of wall cavities. It is done with air movers, dehumidifiers and moisture readings after the standing water is out. Longmont Water Damage Restoration answers water calls for Longmont around the clock, and a crew is dispatched as fast as one is available.

Structural Drying illustration for Longmont, CO

Standing water is only part of a water loss. Once the visible water is gone, the materials that hold the house together still carry moisture, and that moisture keeps causing damage: framing can swell, subfloor can lose strength, and paint and finishes can lift. Structural drying is the work that brings those materials back to a stable moisture level so the damage stops spreading.

Drying is measured, not guessed. A technician uses moisture meters on the framing, the subfloor and the drywall, and compares those readings with readings from unaffected material in the same house. The comparison shows where equipment is needed and when a space is dry enough to close. The eye is a poor judge, because wood can look dry on the surface while its core stays wet.

Flooding has shaped drying work in this area. In September 2013 a City of Longmont document recorded nearly 2,000 homes affected, and FEMA recorded 128 of 960 homes in Lyons as damaged, with 88 judged substantially damaged. Drying the framing and subfloor is often the step that decides what can stay in place. To reach a crew, call (833) 490-5225.

Service area
Longmont & Boulder County
Availability
Phones answered 24/7
Warning signs

Signs you need structural drying

Do not run electrical equipment through standing water, and do not plug in drying equipment on a wet floor. Keep cords off wet surfaces and out of the path of water. Do not cut into a wall or floor to make an opening on your own, because a hidden pipe or wire may be behind it. Gas appliances in the affected area need a technician's check before the space is used again. Plumbing work in the affected area is overseen by the State Plumbing Board within the Department of Regulatory Agencies.

  • A floor that feels soft or gives slightly underfoot after the water is gone
  • Trim, cabinet doors or flooring seams that have shifted or gapped
  • A musty smell that stays in a room after the surface has been dried
  • Paint or wallpaper that lifts a few days after the initial cleanup
  • A damp feel in the wall when a switch plate or outlet cover is removed
  • Warped baseboard that pulls away from the wall at the bottom
  • Floors that feel cool or damp over a crawl space or basement
Our process

How our structural drying visit works

  1. Confirm the water is out

    The crew confirms standing water has been removed and the water source is stopped before any drying equipment is placed. Equipment set up over an active leak only keeps the water moving.

  2. Map the wet materials

    Moisture readings are taken across the framing, subfloor and drywall to map the extent of the wet area. Dry reference readings are recorded from unaffected material in the same house, so the crew has a baseline.

  3. Open what needs airflow

    Small openings are cut in wall cavities and floors where the readings show trapped moisture. Each opening is made to the smallest size that lets air reach the wet material.

  4. Place the equipment

    Air movers and dehumidifiers are positioned for the layout of the affected space. Airflow is set so that air crosses the wet surfaces rather than circulating in one spot.

  5. Monitor and close

    Readings are repeated at set intervals until the wet points return to the dry baseline. The openings are then closed, and the technician records the starting readings, the ending readings and the equipment used.

How does a crew dry the framing and subfloor?

Air is moved across and through the wet materials, and dehumidifiers pull moisture out of that air. Equipment is placed according to the readings and runs until the materials are back to normal.

Air movers are placed to push air over wet surfaces and into wall cavities through the openings the crew has made. Dehumidifiers take moisture out of the room air, which keeps evaporation going from the materials. The crew sets the equipment so that air moves across the whole wet area rather than looping around one spot.

Where the wet material sits inside a closed wall, the crew cuts small openings for airflow and lets the equipment reach the cavity. The openings are sized to the job and closed afterward. The crew does not cut more than the readings require, because each opening is another repair the homeowner has to pay for.

How does a technician know when drying is finished?

Drying is finished when the readings in the wet materials match the readings in unaffected materials nearby, not when the surface looks dry.

A technician records readings at the start and checks them again through the job. Readings are taken at set points in the framing, the subfloor and the drywall, and each point is compared with a dry reference from the same house. The job is done when the wet points come back to the dry baseline.

Surface dryness is not a reliable sign. Wood can appear dry on the outside while the inside stays damp, and that moisture is where swelling and later growth start. The technician keeps the equipment running until the readings settle, and the homeowner then receives the record of the starting and ending points.

Why does wet framing matter after the water is gone?

Wood and other building materials that stay wet can swell, lose strength and support growth. Drying stops those changes from building on one another.

Wood takes up water and swells, which can push trim, cabinets and flooring out of line. A subfloor that stays wet can soften, and a joist or sill plate that softens loses some of its strength. These changes are gradual, so the damage can look finished while it is still developing underneath.

The water path matters too. Water that ran along the bottom plate, into the cavity and under the flooring leaves moisture in several places, not just one. Drying only the visible spot leaves the rest wet, and the damage keeps moving through the building until the whole path is dried.

What moves the cost of structural drying up or down?

The area that is wet, how deep the moisture went into the framing and how much opening is needed for airflow. No price figure is published, and the price is explained and approved before any work starts.

The number of rooms and the depth of moisture are the main factors. A drying job that stays in one room with surface wetness is smaller than one that reaches several rooms and the framing inside the walls. Each additional cavity that must be opened and monitored adds time to the job.

The construction of the house also changes the work. Solid materials and tight finishes take longer to dry than open framing, and carpet pad or tile over a wet subfloor changes how that subfloor is reached. The crew sets out the drying plan on site, and the price is explained and approved before drying begins.

Can drying happen while the homeowner stays in the house?

Often, yes. Drying equipment runs for long periods and is loud and warm, so the homeowner should ask about access and noise before the crew starts.

Air movers and dehumidifiers are left running in the affected area, which can make nearby rooms noisy and warm. The crew sets up the equipment to limit disruption and explains which rooms need to be kept clear. Some rooms may be closed off while drying runs, and the crew says which ones.

Electrical safety comes first. Cords and equipment are routed away from standing water, and the crew checks the outlets in the affected area before power is used there. A homeowner who sees water near an outlet should keep away from it and tell the technician on arrival.

Options

Types and options for structural drying

Wetting under finished floors

Water on a finished floor can soak the subfloor beneath it without showing much on top. The crew checks the subfloor through the floor's edges or a small test opening. Drying runs under and around the floor until the subfloor readings are back to normal.

Wall cavity moisture

Moisture inside a wall often remains after the room has dried on the surface. The crew cuts a small opening, places air movement into the cavity and monitors the framing. The opening is closed only when the readings match the dry baseline.

Ceiling and attic moisture

Water that came down through a ceiling can wet insulation, drywall and the top plates of the walls before anyone sees a stain. The crew checks the ceiling, the insulation above it and the top of the wall framing. Drying is planned for the full water path, not only for the room below.

Crawl space and below-floor moisture

Moisture under a floor can dry slowly, because air moves less freely in a crawl space. The crew checks joists, sills and the subfloor from below and uses equipment suited to the space. The readings show when the space has reached a stable level.

Boulder County

Why structural drying is different in Colorado

The 2013 flood in Lyons is the best local reference for what drying had to do. FEMA counted 128 of 960 homes in Lyons as damaged, and 88 as substantially damaged. Those 88 homes were judged substantially damaged, a finding that turns on the condition of the structure itself, so the framing and subfloor are the parts that decide it.

The St. Vrain River reached a record 24,000 cubic feet per second in Lyons at its peak in 2013. Flows that high can leave water deep in the framing of a house, which is why drying has to reach the structure and not only the floor. The crew's readings in a home near the river record how far the moisture went.

Cold weather brings a different drying question. A pipe that froze and split can wet framing for some time before the leak is found, and the National Weather Service Boulder office listed frozen pipes and water damage among the hazards of its January 2023 event. A technician checks the framing in any room near a cold-exposed line, even when the surface looks dry.

Need structural drying today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Related

Water Heater Leak Cleanup

A leaking tank soaks the floor and the wall at its base. Stop the water, remove what is wet, then dry the framing.

Mold Remediation After Water

Mold follows moisture. Find where the water came from, contain the area, remove the growth and dry the framing.

Crawl Space Water

Water in a crawl space wets the joists, sills and subfloor above it. Remove the water, then dry the structure from below.

Appliance Leak Cleanup

A failed washer hose or dishwasher line spreads water under cabinets and into the subfloor. Stop it, then dry what is wet.

Guides

Read before you book

FAQ

Structural Drying FAQs

How long does drying take?

It takes as long as the readings say it does, which depends on how wet the materials are, how much is wet and how much of the structure is closed in. Some jobs are short, and others run longer because a wall or floor needs more airflow. The technician gives a plan on site and reports the readings as the job goes on.

Can I dry the house faster with my own fans?

Fans help with airflow over surfaces, and a homeowner can run them while waiting for a crew. They do not reach moisture inside walls or under floors, and they can spread dust and contamination if the area is not clean. The crew will ask whether household fans are running so it can plan the equipment around them.

Will the crew remove drywall to dry a wall?

Sometimes. Drywall is removed when the wall is wet and cannot be dried through a small opening, or when the material is soaked enough that it will not recover. The crew cuts the smallest area that lets air reach the cavity. The homeowner is told the reason for each opening.

Why do the readings keep changing during the job?

Readings change as moisture leaves the materials and the air carries it away. Early readings are high, and they fall as the equipment runs. A technician repeats the readings at set intervals and compares them with the dry baseline, so a reading that stops falling tells the crew something is still wrong.

Does drying prevent mold?

Drying removes the moisture that growth needs, so it is the main way to keep growth from starting in the materials. It does not clean growth that is already there, and that work is covered by the mold remediation service. A technician checks for growth during drying and reports it if it is found.

Is the house safe to live in while it is being dried?

Often, yes, with some rooms kept clear. The crew explains which rooms must stay closed and whether the noise and heat will affect sleeping areas. Electrical and gas safety are checked before the space is used, and the homeowner should report any new smell or sound as soon as it appears.

Who confirms that the drying is complete?

The technician does, using moisture readings, and writes the starting and ending readings into the work record. The homeowner can ask to see the readings at any point. A dry result is a measured result, not a visual impression.

WhatsApp